UNIDEN
CORDLESS
TELEPHONES
DXI8560 Series
At Uniden, we'll take care of you!
Thank you for purchasing a Uniden product.
If you have any questions or problems,
please do not return this product to the place of purchase.
Our customer care specialists are here to help you! Visit our website at
during regular business hours.*
Having Trouble?
Need a Part?
To order headsets, additional handsets, replacement batteries or other
during regular business hours.*
Uniden provides a customer service hotline for accessibility questions. If
you have disability and need customer service assistance or if you have any
questions about how Uniden's products can accommodate persons with
disabilities, please call the accessibility voice/TTY line:
1-800-874-9314 (voice or TTY).
Help for our Special
Needs Customers
under the "Accessibility" link. If your call is received outside of our business
hours, leave us a message and we will call you back.
©2007 Uniden America Corporation, Fort Worth, Texas.
Printed in China
UCZZ01065BZ(0)
Place one handset in the base and the other in the charging cradle.
Make sure that the
8
What if the charge LED doesn't
light up?
/in use and LEDs
illuminate.
• Check AC adapter connection.
• Make sure you are not using
an outlet that's controlled by
a wall switch.
Note: For optimum battery life, charge all of your handsets completely before you connect the
telephone cord. The first time you charge a new battery, allow 15 to 20 hours.
1-4. Connect the Telephone Cord
Connect the telephone cord to the
TEL LINE jack on the rear of the base.
9
To TEL LINE
Connect the telephone cord
to a telephone wall jack.
10
To telephone
wall jack
Telephone cord (supplied)
Note: If the telephone cord does not fit into your telephone wall jack, contact your
local phone provider for assistance.
If you receive high-speed internet service through
your telephone line (referred to as DSL), you
should install a DSL filter between the telephone
base and the wall jack. Standard telephones
often can’t operate correctly without a DSL filter.
Telephone
wall jack
DSL filter
Telephone cord
Test the connection
Pick up the handset from the base and press [TALK/flash].
You should hear a dial tone, and the display should showTALK.
11
What if I can't hear a dial tone?
Talk
0:01
Check the telephone cord connection on the base.
What if the display doesn't show TALK?
Put the handset back in the base for at least five seconds.
Make sure the /in use LED flashes.
Make a quick test call, and then press [END] to hang up.
12
What if the call doesn't go through?
Check to see if your telephone provider uses pulse dialing.
(See section 3-1 on System Options.)
What if there is a lot of static?
Check the sources of interference described in section
1-1 on Choosing the best location: is the base near
any of those?
1-5. Register the Accessory Handsets
One by one, put each additional handset in the base.
The /in use LED should flash as the base recognizes the handset.
13
What if the /in use LED
doesn't flash?
Pick the handset up and put it back
in the base.
Wait at least five seconds, then pick up the handset and press
[TALK/flash]. Make sure you can get a dial tone on each handset.
14
1-6. Things to Remember
• When you charge the handsets, the Caller ID summary screen and the
name of the handset appear in the display.
HS1
New :01
Total:17
• Lots of people put HANDSET #1 in the base, but it doesn’t matter which
handset you put in the base and which one you put in the charging cradle.
Now your phone is ready to use!
1-7. Attach the Belt Clip
To attach the belt clip
Insert the tabs on the side of the belt clip into the holes on either side of the handset.
Press the belt clip down until it clicks into place. (Tug on the clip to make sure it’s secure.)
To remove the belt clip
Gently pull the tabs out of the holes, then slide the belt clip off of the handset.
2) Getting to Know Your New Phone
2-1. A few Hints on the Manual
This manual uses several different type styles to help you distinguish between different parts of the phone:
• Bold text with “[ ]”indicates a key or button on the phone
• ALL CAPITALS indicates text on the display, such as menu options, prompts, and confirmation messages
• lower case bold text indicates a status light on the phone
Terms used in this manual
The main part of the phone that connects to your phone line and lets you make and receive
calls.
Base
Charging A cradle that charges the handset battery. It connects to power but does not connect to a
cradle
phone line.
Caller ID is available from your telephone provider. With this service, you can see the name and
number of incoming callers.
CID
Caller ID on Call Waiting is available from your telephone provider. With this service, you can
see incoming caller information while on another call.
CIDCW
A cordless handset that can be placed anywhere in your home or office where AC power is
available.
Handset
The phone is not in use. (It doesn’t matter whether the handset is in the cradle: the [TALK/
Standby
Talk
flash] hasn’t been pressed, and there is no dial tone.)
A dial tone has been enabled, so you can dial and carry on a conversation with an outside party.
Note: Illustrations in this manual are used for explanation purposes and may differ from the actual unit.
2-3. Parts of the Handset
Earpiece
LCD display
key (up)
/memory key
(phonebook/memory)
cid/menu key
TALK/flash key
END key
key (down)
Twelve-key dial pad
#/ key (#/right)
/tone/ key(*/tone/left)
redial/pause key
/speaker key
delete/transfer key
select/channel key
Microphone
Charging contacts
Using the handset menu
• To open the handset menu, press and hold [cid/menu] for two seconds.
• The arrow pointer on the left side of the line shows which menu item is
currently highlighted. Use [ ] to move the pointer up and [ ] to move
the pointer down.
• If the phone beeps and stays on the same line, it means you have reached
the top or bottom of the list.
• Press [select/channel] to rotate through the available options for the
highlighted menu item.
• Press [END] to exit the menu.
Ringer :Type A
Ring. Vol.:High
Auto Talk :Off
CIDCW
Area Code :
Dial :Tone
:On
Note: You can find detailed information on the handset menu in section 3 on
Setting Up Your Phone and section 4 on Using Your Phone.
Language :Eng
(HS1 display)
2-4. Parts of the Base
Charging contacts
in
use
find hs
/in use LED/
Voice mail waiting indicator (flashing)
find hs key
3) Setting Up Your Phone
Your phone has four basic options that you need to set up first. You should only have to set these options once,
and you may not have to change any of them: Dial mode (tone or pulse dialing)
• Dial mode (tone or pulse dialing)
• CIDCW (Caller ID on Call Waiting)
• Language
• Auto talk
You might change two handset-specific options --ringer type and ringer volume -- more often, depending on
the situation. There’s another option, area code, that you should only set if you can use seven-digit dialing (see
section 5-3 on Using Seven Digits Instead of Ten).
3-1. System Options (from HS1 only)
These options can only be changed from handset 1 (HS1). After changing these settings, you must put HS 1
back in the base cradle to activate them.
Changing from tone to pulse dialing (DIAL)
Your phone can communicate with the telephone network in two different ways: tone dialing or pulse dialing. These
days, most phone networks use a method called tone dialing, so your phone comes programmed for tone dialing.
If your phone company uses pulse dialing, you need to change your phone’s dial settings. If you don't get a dial
tone or can't connect to the telephone network, follow the steps below to modify your phone’s settings:
1) Make sure you have Handset 1 (HS 1).
2) With the phone in standby, press and hold [cid/menu].
3) Press [ ] to move the pointer to DIAL.
4) Press [select/channel] to set the phone to pulse dialing.
5) Press [END] and put the handset back in the base. Handset 1 communicates the new setting to the base,
and the base activates the setting on any other handsets.
Note: If you use pulse dialing and you need to send DTMF tones during a call (if you're using an automated
response system, for example), press [ /tone/ ] to temporarily switch to tone dialing. When the call
ends, the phone automatically returns to pulse dialing mode.
Activating Caller ID on Call Waiting (CIDCW)
You must subscribe to Caller ID service through your local telephone provider to use this feature.
Caller ID allows you to see the name and number of the calling party before you answer the phone. Caller ID on
Call Waiting (CIDCW) lets you see the name and number of a call that comes in when you are on the line.
1) Make sure you have Handset 1 (HS 1).
2) With the phone in standby, press and hold [cid/menu].
3) Press [ ] to move the pointer to CIDCW.
4) Press [select/channel] to toggle and turn on Caller ID on Call Waiting.
5) Press [END] and put the handset back in the base. Handset 1 communicates the new setting to the base,
and the base activates the setting on any other handsets.
3-2. Handset-specific Options
These options can be set differently on each handset. You can also set these options while another handset is
using the phone.
Setting the display language (LANGUAGE)
The handset menus can use English (ENG, default), French (FR.) or Spanish (ESP).
1) With the phone in standby, press and hold [cid/menu].
2) Press [ ] to move the pointer to LANGUAGE.
3) Press [select/channel] to select ENG, FR. or ESP.
4) When the display shows the language you want, use [ ] and [ ] to move the pointer to another menu
item.
OR
If you’re finished, press [END] to return the handset to standby.
Activating AutoTalk (AUTO TALK)
With Auto Talk, you can answer the phone just by picking up the handset from the cradle: you don’t have to
press any keys. If the handset is already off the cradle, Auto Talk also lets you answer by pressing any key on the
twelve-key dial pad (instead of just [TALK/flash]).
1) With the phone in standby, press and hold [cid/menu].
2) Press [ ] to move the pointer to AUTO TALK.
3) Press [select/channel] to turn Auto Talk on.
4) Use [ ] and [ ] to move the pointer to another menu item.
OR
If you’re finished, press [END] to return the handset to standby.
Setting the ringer tone (RINGER)
You can set the ring tone separately for each handset.
1) With the phone in standby, press and hold [cid/menu].
2) Press [select/channel] to rotate through the four available ring tones (A, B, C, and D). As you switch to the
next ring tone, the handset sounds a sample of that ringer.
3) When you hear the ringer you want, use [ ] and [ ] to move the pointer to another menu item.
OR
If you’re finished, press [END] to return the handset to standby.
The handset will use the new ring tone starting with the next incoming call.
Setting the handset ringer volume (RING.VOL.)
You can choose from three ringer volume settings separately for each handset. To turn the ringer off, select
RINGER OFF.
1) With the phone in standby, press and hold [cid/menu].
2) Press [ ] to move the pointer to RING VOL.
3) Press [select/channel] to rotate through the three available volume levels (HIGH, LOW, and OFF). As you
switch to the next volume level, the handset sounds a sample of the current ring tone at that level.
4) When you hear the volume level you want, use [ ] and [ ] to move the pointer to another menu item.
OR
If you’re finished, press [END] to return the handset to standby.
The handset will use the new ringer volume starting with the next incoming call.
Note: If you set the ring volume to OFF, this handset won’t ring. The other handset(s) will ring according to their
individual settings.
4) Using Your Phone
4-1. Making and Receiving Calls
...from a handset
...from a handset speaker phone
1) Pick up the handset.
1) Pick up the handset.
2) Press [TALK/flash].
3) Listen for the dial tone.
4) Dial the number.
OR
2) Press [
].
3) Listen for the dial tone.
4) Dial the number.
OR
To make a
call...
1) Pick up the handset.
2) Dial the number.
3) Press [TALK/flash].
1) Pick up the handset.
2) Dial the number.
3) Press [
].
1) Pick up the handset. (If AutoTalk is on, the
phone automatically answers when you pick it
up from the cradle.)
2) Press [TALK/flash]. (If Auto Talk is on, you can
also press any key on the twelve-key dial pad.)
1) Pick up the handset.
2) Press [ ].
To answer a
call...
To hang up... Press [END] or return the handset to the cradle.
4-2. Switching a Call to the Handset Speakerphone
To switch a normal call to the speakerphone, press [
] again.
] on the handset. To switch back to a normal call, press
[
4-3. Transferring a Call
You can transfer a call from one handset to another.
Note: Only one handset at a time can talk with an outside caller. While one handset is in use, other handsets
cannot listen to conversations or make an outgoing call.
1) During a call, press [delete/transfer]. This places the call on hold.
2) Press the number key that matches the handset you want to page (1 for Handset 1, 2 for Handset 2, etc.) or
press 0 to page all other handsets. (If you only have two handsets, the phone automatically pages the second
handset for you.)
3) The handset display shows LINE ON HOLD along with the number of the
handset you are paging. Both your handset and the paged handset sound
a paging tone that is distinct from any of the available ringer tones.
4) If the other handset picks up the call, the paging tone stops, and your
handset returns to standby.
Line on Hold
Transfer to HS1
• To cancel the transfer and return to the caller, press [delete/transfer], [TALK/flash] or [
• If no one picks up the transferred call within five minutes, the call will be disconnected.
].
To receive a transfer call
When a handset receives a transfer page, it sounds the distinct paging tone and shows CALL TRANSFERRED in
the display. To answer a transferred call, pick up the handset and press [TALK/flash] or [
]. (If Auto Talk
is on, the phone automatically answers when you pick it up from the cradle; if the handset is already off the
cradle, you can also press any key on the twelve-key dial pad.)
4-4. Redialing the Last Dialed Number
1) Pick up the handset from the cradle.
1) Pick up the handset from the cradle.
2) Press [redial/pause].
3) Press [TALK/flash] or [
2) Press [TALK/flash] or [
3) Listen for the dial tone.
4) Press [redial/pause].
].
OR
].
4-5. Adjusting the Speaker Volume
You can change the speaker volume on the handset earpiece, or the handset speakerphone.
When you are on a normal call, press [ ] to make the earpiece louder or [ ] to make it softer.
The handset display shows the current volume level for the earpiece.
When you are using the speakerphone, use [ ] or [ ] to change the speaker volume. The handset display
shows the current volume level for the handset speakerphone.
There are four volume levels: LOW, MEDIUM, HIGH, and MAXIMUM.
Notes:
•
•
The handset earpiece and the handset speakerphone have separate volume settings.
If you hear three quick error beeps, it means the earpiece or speaker is already at the lowest (LOW) or highest
(MAXIMUM) volume level.
4-6. Finding a Lost Handset
To locate a lost handset, press [find hs] on the base. All registered handsets will beep for sixty seconds.
To cancel paging, press [find hs] again or press any key on the found handset.
4-7. Muting the Ringer
When the phone is ringing, you can mute the ringer on the handset. Muting stops the ringer for the current call
only: the ringer will sound with the next incoming call. You can only mute the handset ringer if the handset is
already off the cradle when the handset starts ringing. Press [END] to mute the incoming ring.
4-8. Voice Mail Waiting Indicator
If you subscribe to voice mail service through your local telephone company, you can use your cordless
telephone to access your voice mailbox. The voice mail company will provide you with the access number.
The /in use LED on the base of your phone flashes whenever you have messages waiting in your voice mailbox.
To access your voice mailbox
Just dial the access number supplied by your voice mail provider to enter your mailbox. You can program your
voice mail access number to a speed dial number.
If the voice mail waiting indicator remains on after you have retrieved your messages, press and hold [find hs]
for five seconds. This will reset the indicator.
4-9. Using an Optional Headset
• To install a headset, remove the headset jack cover and insert the headset plug
into the headset jack.
• When you connect a headset, the earpiece and speakerphone are automatically
muted. If you want to re-activate the earpiece or speakerphone, remove the
headset plug.
• You will still make and receive calls as usual: just use your headset to talk to the
caller once the call connects.
• You can purchase headsets from our website at www.uniden.com or by calling our Parts Department (See the
back cover page).
5) Using Caller ID and Call Waiting
If you subscribe to Caller ID from your phone company, your phone will show you the caller's phone number and
name (if available) whenever a call comes in. If you subscribe to both Call Waiting and Caller ID, the phone also
shows you the name and the number of any call that comes in while you're on the line.
The date and time received
5/11 12:30PM
Caller's name
Jane Smith
Caller's Phone Number
214-555-1234
Note: If you answer a call before the Caller ID record is received (for example, before the second ring), the Caller
ID record will not appear.
The phone stores the Caller ID information for up to thirty incoming calls - even unanswered calls. If the phone
receives more Caller ID records than it can store, the oldest record in the list is automatically deleted.
For information on storing Caller ID records in the phonebook, see section 6-6.
5-1. Reviewing the Caller ID Record List
You can review the Caller ID list when the handset is in standby or during a call.
1) Press [cid/menu]. The summary screen displays the total number of CID
records along with the number of new CID records (that is, calls that you
haven't reviewed yet).
2) Use [ ] to scroll through the records from the latest to the earliest, or
use [ ] to scroll through the records from the earliest to the latest.
Caller ID
New :01
Total:17
3) Press [cid/menu] to exit the Caller ID list.
For new Caller ID records, the phone keeps a count of the number of calls
received from the same caller (instead of saving the information multiple
times). The Caller ID record shows the time and date of the most recent call
from that number, and the number of calls appears next to the received time.
The phone only maintains this count for new or “unviewed”records: once you
review that record, the number is cleared.
12/30 11:59PM 01
Jane Smith
214-555-1234
5-2. Making a Call from the Caller ID List
1) With the phone in standby, press [cid/menu].
2) Use [ ] or [ ] to find the Caller ID record you want to call.
3) If you need to add or delete a “1”from the displayed phone number, press [1].
What’s this “add or delete a 1”about?
• Any phone number in the Caller ID records might (or might not!) have a “1”at the front, depending on how
different phone companies send the Caller ID information.
• The phone dials the number exactly as it appears in the Caller ID record.
• If the phone number is a long distance or toll call, but the Caller ID record does not have a “1”in front of the
number, press [1] to add it.
• If the phone number is a local or non-toll call, but the Caller ID record has a “1”in front of the number, press
[1] to delete it.
4) Press [TALK/flash] or [
] to dial the number.
] before you access the Caller ID list. When you come to the
Note: You can also press [TALK/flash] or [
phone number you want to dial, press [select/channel].
5-3. Using Seven Digits Instead of Ten
If you can make a local call by dialing only seven digits instead of ten, you can tell the phone to hide your local
area code in the Caller ID list; any calls from outside your area code will show all ten digits.
Entering your area code
You can enter the area code in each handset separately (for example, if you want to hide the area code on one
handset but not another):
1) With the phone in standby, press and hold [cid/menu].
2) Press [ ] to move the pointer to select AREA CODE. If an area code was already stored, the handset will
display it.
3) Press [select/channel] to edit the area code.
4) Use the number keys ([0] – [9]) to enter all three digits of your area code.
If you make a mistake, press [delete/transfer] to erase the last digit.
5) When the number is correct, press [select/channel]. A confirmation tone sounds.
6) Press [END]. The handset returns to standby.
• The phone uses the stored area code as a filter. When a call comes in, the phone compares the incoming area
code to the code programmed in the handset. If the two codes match, the handset hides the area code in the
Caller ID list.
• When you’re in the Caller ID list, you can show the hidden area code by pressing [3]. Press [3] again to hide
the area code.
When you dial from a Caller ID list or store a Caller ID record in the phonebook, the phone dials or stores the
digits exactly as they appear on the display. If you need to use ten digits, be sure to press [3] to show the area
code before you dial or store the number. See Section 6-6, Storing Caller ID Records in the Phonebook.
5-4. Deleting Caller ID Records
• Caller ID records are stored separately in each handset. Deleting a record from one handset will not delete the
record from any other handsets.
• If you get an incoming call or page, the operation is canceled.
To delete one Caller ID record
To delete all the Caller ID records
1) With the phone in standby, press [cid/menu].
1) With the phone in standby, press [cid/menu].
2) Use [ ] or [ ] to find the Caller ID record you 2) From the CID summary screen, press [delete/
want to delete.
transfer]. The display asks you to confirm.
3) Press [delete/transfer]. The display asks you to 3) To delete all the records, use [ ] to move the
confirm.
pointer to YES. Or, if you changed your mind, leave
the pointer at NO.
4) To delete the record, leave the pointer at YES. Or,
if you changed your mind, press [ ] to move the 4) Press [select/channel] to confirm.
pointer to NO.
5) Press [select/channel] to confirm.
5-5. Using Call Waiting
If you subscribe to Call Waiting and a second call comes in when you are on
Talk
0:54
the phone, the phone sounds a call waiting tone. If you also have Caller ID
service, the phone shows the Caller ID information for the incoming call. (Only
the handset that’s on a call when the call came in can see and store the Caller
ID information.)
Jane Smith
214-555-1234
To put the original call on hold and switch to the waiting call, press [TALK/flash]. After a slight pause, you are
connected to the new caller. Press [TALK/flash] again to switch back to the original caller.
OR
To hang up and answer the new call, press [END]. The phone disconnects the original caller and switches to the
new caller.
6) Using the Phonebook (speed dial memory)
• If you enter phone numbers (along with names) into the handset’s phonebook/speed dial memory, you can
dial them with just two key presses.
• Each handset can store ten different phonebook entries (corresponding to 0 through 9 on the number
keypad); phonebook entries are separate for each handset.
• You can use the phonebook to store any number up to twenty digits. This is useful if you have a series of digits
that you need to enter after your call connects, such as an access code or account number (See section 6-7 on
Chain Dialing).
•
When you’re editing the phonebook, you must press a key within thirty seconds or the phone will return to standby.
6-1. Entering a New Number into the Phonebook
1) With the phone in standby, press [ /memory] to open the phonebook
01 Jane Smith
02 <Empty>
list.
2) Enter a number ([0] – [9]) or press [ ] or [ ] to find a phonebook
entry that shows <EMPTY> beside it, and press [select/channel]. The
handset opens the STORE NAME screen.
03 <Empty>
3) Use the letters above the number keys to enter a name for this phonebook
entry. Press [select/channel] when you’re finished (or if you don't want
to enter a name). The handset opens the STORE NUMBER screen.
Store Name
｡
Entering text in your phone
The letters above the number appear in order: press the 2 key once for A, twice for B, and three times for C.
You can also enter lower case letters and symbols (see the table below for all the available characters and
what keys to press to enter them).
Number of times key is pressed
For example, to enter Mom
1) Press [6] once to enter M.
2) Press [#/ ] to move the cursor to the
right.
3) Press [6] six times to enter o.
4) Press [#/ ] to move the cursor to the
right.
5) Press [6] four times to enter m.
• New characters are inserted next to the
character highlighted by the blinking
cursor.
keys
1
1
2
3
4
5
6
7
8
9
A B C a b c 2
D E F d e f 3
G H I g h i 4
J K L j k l 5
M N O m n o 6
P Q R S p q r s 7
T U V t u v 8
W X Y Z w x y z 9
• To enter between characters, move the
cursor and enter a new character.
(blank)
* # - & ( )
0
• Use [ /tone/ ] and [#/ ] to move the cursor to the desired location.
• To enter two characters controlled by the same key, enter the first character, move the cursor to the right,
then enter the second character.
• When the cursor is on the end of the digit, press [delete/transfer] to delete characters from last one as
needed.
• If you made a mistake, move the cursor to the incorrect character and press [delete/transfer]. Then enter
the correct character.
• To delete all the characters, press and hold [delete/transfer].
4) Use the number keypad to enter the phone number. Press [select/
Store Number
channel] when you’re finished. The handset sounds a confirmation tone
and displays MEMORY STORED.
8007303456｡
• The number can be up to twenty digits.
• If this phone number is a long distance call, be sure to include the “1”
in front of the phone number.
• If you need the phone to wait before dialing the next digit (for example, to enter an extension number
or access code), press [redial/pause] to insert a two-second pause between digits. The display shows
a P where the phone will pause. You can add as many pauses as you want anywhere in the phone
number, but each pause does count as a digit.
5) After a few seconds, the handset goes back to the phonebook list. Use [ ] and [ ] to select another
phonebook entry.
OR
Press [ /memory] to exit the phonebook. The phone returns to standby.
6-2. Finding Phonebook Entries
If you know the number of the phonebook entry you're looking for:
• Press and hold the number key (0 through 9) assigned to that phonebook entry.
The handset displays the name and phone number saved for that phonebook entry. If the entry has no
number, the handset displays : <EMPTY> PRESS SELECT TO EDIT.
• If the number you picked wasn't the right phonebook entry, just use [ ] and [ ] to scroll through the
phonebook entries. Stop scrolling when you see the phonebook entry you want.
If you don't know the number of the phonebook entry you're looking for:
• Press [ /memory] to open the phonebook list.
• Use [ ] and [ ] to scroll through the phonebook entries. Stop scrolling when you see the phonebook
entry you want.
6-3. Making a Call from the Phonebook
With the phone in standby, find the phonebook entry you want to call (See section 6-2 on Finding Phonebook
Entries). Then press [TALK/flash] or [
You can also press [TALK/flash] or [
[select/channel].
] to dial the number.
] and then find the phonebook entry you want to call, and press
6-4. Editing a Number in the Phonebook
1) With the handset in standby, find the phonebook entry you want to edit (See section 6-2 on Finding
Phonebook Entries).
2) Press [select/channel] to open the MENU screen.
3) On the MENU screen, use [ ] to move the pointer to EDIT MEMORYXX, and press [select/channel].
4) The handset takes you to the STORE NAME screen from Step 2 of section 6-1 on Entering a New Number into
the Phonebook: just follow the same steps from there.
6-5. Deleting a Number from the Phonebook
1) With the handset in standby, find the phonebook entry you want to delete (See section 6-2 on Finding
Phonebook Entries).
2) Press [select/channel] to open the MENU screen.
3) On the MENU screen, use [ ] to move the pointer to DELETE MEMORYXX, and press [select/channel]. The
handset asks you to confirm.
4) To delete the entry, use [ ] to move the pointer to YES and press [select/channel]. The handset sounds a
confirmation tone and goes back to the phonebook list.
OR
If you changed your mind, leave the pointer at NO and press [select/channel]. The handset goes back to the
phonebook list.
6-6. Storing Caller ID Records in the Phonebook
1) With the phone in standby, press [cid/menu].
2) Use [ ] or [ ] to find the Caller ID record you want to save.
Note: Remember, the phone stores the digits exactly as they appear on the display. If you need to add or delete a
"1" from the displayed phone number, press [1]. (You can always go back and edit the phone number later.)
3) Press [ /memory] to open the phonebook.
4) Find the phonebook entry number you want to use (See section 6-2 on Finding Phonebook Entries).
5) Press [select/channel] to store the Caller ID information to the phonebook and return to the Caller ID list.
Note: If this number already has a phonebook entry saved to it, the handset asks if you want to replace the
existing entry. Select YES to replace the existing entry with the new one, or select NO to cancel and keep
the existing entry. The display returns to the Caller ID list.
6-7. Chain Dialing
If you often have to enter a series of digits or some type of code number during a call, you can save that code
number to a phonebook entry. When your call connects, just use the phonebook speed dial to transmit the
saved code number. (This is referred to as chain dialing.)
1) Enter the code number (up to twenty digits) into the phonebook (See section 6-1 on Entering a New Number
into the Phonebook). Be sure to enter the code number into the phonebook exactly as you would enter it
during a call.
2) During a call, when you hear the prompt that tells you to enter the code number, press [ /memory] to
open the phonebook.
3) Find the phonebook entry number you want to use (See section 6-2 on Finding Phonebook Entries).
4) Press [select/channel]. The phone sends the digits of the code number exactly as you saved them in the
phonebook entry.
7) Mounting the Base on a Wall
You can mount the phone on any standard telephone jack wall plate.
Route the AC adapter and the telephone
1
cords through the hole of the wall
mount bracket.
Connect the AC adapter and the
2
telephone cords as shown.
Remember to route the AC adapter
cord through the channel.
Line up the four tabs on the wall mount bracket (two at the top and
3
two at the bottom) with the four notches on the bottom of the base.
Slide the bracket into place.
Plug the telephone cord
5
into the wall jack.
Hook the AC adapter cord
into the smaller notch at
the bottom of the bracket,
and let the cord hang
below the bracket.
Hook both sides of the
telephone cord into the
larger notch
4
OR
tuck the excess cord into the
open space in the bracket.
Wall plate
To AC outlet
To telephone
wall jack
AC adapter (supplied)
Telephone cord (supplied)
Place the mounting slots over the pins on the wall plate.
6
Wall plate
Slide the base down to lock it into place.
7
Note: To mount the phone directly on the wall, insert two 1 3/8 inch, #10 screws (not supplied) into the wall
using anchors suitable for the wall material. Place the screws 3 15/16 inches apart, and allow 1/8 inch free
space between the wall and screw heads.
To remove the wall-mount bracket
At the bottom of the base, lift up on the release latch and
push the bracket up.
Release latch
8) Troubleshooting and Maintenance
8-1. Solving Common Issues
If your phone is not performing to your expectations, please try these simple steps first. If these steps do not
solve your problem, please call our Customer Hotline. See back cover page for contact information.
When you have this problem…
Try…
The /in use LED or LED won't • Checking the AC adapter connection.
turn on when the handset is placed • Re-seating the handset in the cradle.
in the cradle.
• Cleaning the charging contacts on the handsets (See section 8-8).
• Moving the handset closer to the base.
• Moving the handset and/or base away from metal objects or
appliances and try again.
• Changing the channel by pressing [select/channel] during a call.
This can help eliminate background noise.
The audio sounds weak and/or
scratchy.
• Checking the telephone cord connection.
No handsets can make or receive • Disconnecting the AC adapter. Wait a few minutes, then reconnect it.
calls.
• Asking your telephone company if they use pulse dialing (See section
3-1).
• Charging the battery for 15-20 hours.
A single handset can’t make or
receive calls.
• Moving the handset closer to the base.
• Changing the handset-to-base code (See section 8-3).
A handset can make calls, but it
doesn’t ring.
• Making sure the ringer isn’t turned off (see section 3-2).
A handset’s display doesn’t show • Charging the battery for 15-20 hours.
anything. • Checking the battery pack connection.
When you have this problem…
Try…
• Changing the channel by pressing [select/channel] during a call to
help eliminate background noise.
• Keeping all handsets away from microwave ovens, computers, remote
control toys, wireless microphones, alarm systems, intercoms, room
monitors, fluorescent lights, and electrical appliances.
• Moving the base to a better location (see section 1-1).
There’s a lot of static during calls.
• Letting incoming calls ring at least twice before answering.
• Checking to see if the call was placed through a switchboard.
• Checking with your telephone service provider to make sure your
Caller ID service is active (See section 5).
The handset won’t display any
Caller ID information.
• Checking the battery pack connection.
• Charging the battery for 15-20 hours.
A handset is not working.
• Changing the handset-to-base code (See section 8-3).
• Moving the handset closer to the base.
• Seeing if another handset is on a call or checking messages.
(Two handsets can’t communicate to the base at the same time.)
• Making sure the base is plugged in.
A handset says “Unavailable”.
I can’t transfer calls.
• Changing the handset-to-base code (See section 8-3).
• Changing the handset-to-base code (See section 8-3).
• Only one handset at a time can talk with an outside caller. To allow
the other handset to talk to the caller, transfer the call (See section
4-3).
I can’t get two handsets to talk to
the caller.
• Contact your local telephone company to make sure that your
telephone receives FSK message signaling.
• Reset the indicator by pressing and holding [find hs] for five seconds.
The Voice Message Waiting
Indicator does not work.
8-2. Re-registering Handsets
When you first put your handsets into the base, they are registered to the base so they can communicate with
the base. There may be some times when you have to re-register your handsets to the base:
•
•
•
When you want to change the handset-to-base code.
When there is a power failure that lasts more than one hour.
If a handset's battery is completely discharged. (The handset must be recharged for 15 - 20 hours before re-
registering to the base.)
•
Any time you experience difficulty connecting to the base to make or receive calls.
To re-register handsets:
1) Pick up the handset from the base. Press and hold [find hs] on the base.
2) While holding [find hs], place the handset in the base. The /in use LED on the base begins to flash,
indicating the base is registering the handset. Wait for at least five seconds.
3) Pick up the handset from the base and press [TALK/flash]. If the display shows TALK, the handset is
registered. If not, place the handset in the base to try again.
4) Press [END].
5) One by one, place each handset in the base and wait for at least five seconds. (You don't need to hold [find
hs] this time.) Repeat steps 3 - 4.
8-3. Changing the Handset-to-base Code
The handset-to-base code prevents other cordless devices from accidentally connecting to your base. If the
battery pack is completely discharged or removed, the handset can "forget" the handset-to-base code, and the
handset will not be able to communicate with the base.
If any one of handsets can't communicate with the base, place that handset in the base cradle to reset the code. Wait
at least five seconds, then pick up the handset and press [TALK/flash]. If the display shows TALK, the code is reset.
If the code does not reset or if you suspect another cordless telephone might be using the same code (a rare
situation), you can change the handset-to-base code completely. Re-register all handsets to the base following
the instructions in section 8-2 on Re-registering Handsets above. Any handsets that are not properly re-
registered may not be able to communicate with the base.
8-4. Traveling Out of Range
During a call, as you begin to move your handset too far from your base, noise increases. If you pass the range
limits of the base, your call will terminate within one minute.
8-5. Liquid Damage
Moisture and liquid can damage your cordless phone.
• If the handset or base is exposed to moisture or liquid, but only the exterior plastic housing is affected, wipe
off the liquid, and use as normal.
• If moisture or liquid has entered the plastic housing (i.e. liquid can be heard in the phone or liquid has entered
the handset battery compartment or vent openings on the base), follow the steps below:
Handset
Base
1) Remove the battery cover and leave it off for ventilation.
2) Disconnect the battery pack. Leave the battery cover off and the
battery pack disconnected for at least three days.
1) Disconnect the AC adapter
from the base, cutting off
electrical power.
3) Once the handset is completely dry, reconnect the battery pack and 2) Disconnect the telephone cord
the battery cover.
from the base.
4) Recharge the handset's battery pack for 15 to 20 hours before using. 3) Let dry for at least three days.
IMPORTANT:
You must unplug the telephone line while recharging the battery pack to avoid charge interruption.
CAUTION!
DO NOT use a microwave oven to speed up the drying process. This will cause permanent damage to the
handset, base and the microwave oven. After following these steps, if your cordless telephone does not work,
please call our Customer Service Hotline. See back cover page for contact information.
8-6. Specifications
The phone complies with FCC Parts 15 and 68.
Operating temperature 0°C to +50°C (+32°F to +122°F)
For the base
PS-0003
120V AC 60Hz
9V DC 350mA
BT-905
For the charging cradle
PS-0007
120V AC 60Hz
Part number
Input Voltage
Output Voltage
Part number
Capacity
AC Adapter
9V DC 210mA
Battery
600mAh, 3.6V
921.103102 – 923.787761 MHz
5,856.533347 – 5,863.692437MHz
Frequency
Note: To avoid damage to the phone, use only Uniden PS-0003, PS-0007 and BT-905 with your phone.
Specifications, features, and availability of optional accessories are all subject to change without prior notice.
8-7. Power Failure Operation
During the period that the power is off, you will not be able to make or receive calls with the telephone.
8-8. Battery Information
Average battery life
With average use, your handset battery provides approximately six hours of talk time and approximately seven
days of standby time. You can achieve optimum battery life and performance by returning the handset to the
cradle after each use. When your handset is left off of the cradle, the battery will gradually discharge even if the
handset is not being used. The actual talk time duration will be reduced in proportion to the amount of time the
handset is off the cradle.
Low battery alert
When the battery pack is very low and needs to be charged, the phone is
programmed to eliminate functions in order to save power. If the phone is not
in use, LOW BATTERY CHARGE HANDSET appears on the LCD, and none of the
Low Battery
keys will operate. During a call, the handset beeps, and the LCD flashes LOW
Charge Handset
BATTERY. Complete your conversation as quickly as possible and return the
handset to the cradle for charging.
Note: Information stored in the phone's memory will be retained for thirty minutes after the battery pack is
removed. This includes all setup information, last number dialed, speed dial memory, and the CID list.
Battery replacement and handling
When the operating time becomes short even after a battery is recharged, please replace the battery. With
normal usage, your battery should last about one year. To order replacement batteries, please contact Uniden’s
Parts Department. The contact information is listed on the back cover page.
Warning:
To avoid the risk of personal injury or property damage from fire or electrical shock, only use the Uniden
battery packs and power adapters specifically designated for this product.
Caution:
• Use only the specified Uniden battery pack (BT-905).
• Do not remove the battery from the handset to charge it.
• Never throw the battery into a fire, disassemble it, or heat it.
• Do not remove or damage the battery casing.
Cleaning the charging contacts
To maintain a good charge, clean the charging contacts on the handset
once a month. Dampen a cloth with plain water. Gently rub the damp
cloth over the charging contacts until all visible dirt is removed. Dry the
contacts thoroughly before returning the handset to the cradle.
Contacts
Caution:
Do not use paint thinner, alcohol, or other chemical products. Doing so may discolor the surface of the
telephone and damage the finish.
9) Legal and Warranty Information
9-1. Precautions!
Before you read anything else, please note the following:
Warning!
Uniden America Corporation DOES NOT represent this unit to be waterproof. To reduce the risk of fire,
electrical shock, or damage to the unit, DO NOT expose this unit to rain or moisture.
9-2. Rechargeable Nickel-Cadmium Battery Information
This equipment contains a rechargeable nickel-cadmium battery.
•
•
•
•
Cadmium is a chemical known to the State of California to cause cancer.
The rechargeable nickel-cadmium battery contained in this equipment may explode if disposed of in a fire.
Do not short-circuit the battery.
Do not charge the rechargeable nickel-cadmium battery used in this equipment in any charger other than the one designed
to charge this battery as specified in the owner's manual. Using another charger may damage the battery or cause the
battery to explode.
•
•
Rechargeable Nickel-Cadmium Batteries Must Be Recycled or Disposed of Properly
As part of our commitment to protecting our environment and conserving natural resources, Uniden
voluntarily participates in an RBRC® industry program to collect and recycle used Ni-Cd batteries
within the United States. Please call 1-800-8-BATTERY for information on Ni-Cd battery recycling in
your area. (RBRC® is a registered trademark of the Rechargeable Battery Recycling Corporation.)
9-3. Lead Content Information
Warning!
The cords on this product and/or accessories contain lead, a chemical known to the State of California to
cause birth defects or other reproductive harm. Wash hands after handling.
Uniden works to reduce lead content in our PVC coated cords in our products and accessories.
9-4. Important Safety Instructions
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric
shock and injury to persons, including the following:
1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet
basement or near a swimming pool.
2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric
shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode.
Check with local authorities for possible battery disposal instructions.
5. Do not disassemble any component of this product.
SAVE THESE INSTRUCTIONS
CAUTION!
Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Do not
open or mutilate the battery, and disconnect the battery before shipping this product.
9-5.The FCC Wants You To Know
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA.
On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US:
AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.
An applicable Universal Service Order Codes (USOC) certification for the jacks used in this equipment is provided (i.e., RJ11C)
in the packaging with each piece of approved terminal equipment. A plug and jack used to connect this equipment to the
premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the
ACTA.
A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible
modular jack that is also compliant. See installation instructions for details.
The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone
line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should
not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs,
contact the telephone provider. For products approved after July 23, 2001, the REN for this product is part of the product
identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is
a REN of 0.3). For earlier products, the REN is separately shown on the label.
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary
discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the
customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is
necessary. The telephone company may make changes in its facilities, equipment, operations or procedures that could
affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for
you to make necessary modifications to maintain uninterrupted service. Please follow instructions for repairing, if any
(e.g. battery replacement section); otherwise do not substitute or repair any parts of the device except as specified in this
manual. Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service
commission or corporation commission for information. This equipment is hearing aid compatible.
Should you experience trouble with this equipment, please contact Uniden customer service at 800-297-1023. If the
equipment is causing harm to the telephone network, the telephone company may request that you disconnect the
equipment until the problem is resolved.
NOTICE: According to telephone company reports, AC electrical surges, typically resulting from lightning strikes, are very
destructive to telephone equipment connected to AC power sources. To minimize damage from these types of surges, a surge
arrestor is recommended.
Changes or modifications to this product not expressly approved by Uniden, or operation of this product in any way other than
as detailed by the owner's manual, could void your authority to operate this product.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) This device must accept any interference received, including interference that may
cause undesired operation. Privacy of communications may not be ensured when using this phone.
Cordless telephone privacy
Cordless telephones are radio devices. Communications between the handset and base of your cordless telephone are
accomplished by means of radio waves which are broadcast over the open airways. Because of the inherent physical
properties of radio waves, your communications can be received by radio receiving devices other than your own cordless
telephone unit. Consequently, any communications using your cordless telephone may not be private.
9-6. I.C. Notice
Terminal equipment
NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed
by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed
based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that
Industry Canada approved the equipment.
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is marked on the equipment itself. The REN
assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected
to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the
requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five.
Radio equipment
The term "IC:" before the radio certification number only signifies that Industry Canada technical specifications were met.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device. "Privacy of communications
may not be ensured when using this telephone".
9-7. One Year Limited Warranty
Important: Evidence of original purchase is required for warranty service. WARRANTOR: UNIDEN AMERICA CORPORATION
("Uniden") ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail owner, this Uniden Product to be
free from defects in materials and craftsmanship with only the limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original user shall terminate and be of no further effect 12 months after the date
of original retail sale. The warranty is invalid if the Product is (A) damaged or not maintained as reasonable or necessary,
(B) modified, altered, or used as part of any conversion kits, subassemblies, or any configurations not sold by Uniden, (C)
improperly installed, (D) serviced or repaired by someone other than an authorized Uniden service center for a defect or
malfunction covered by this warranty, (E) used in any conjunction with equipment or parts or as part of any system not
manufactured by Uniden, or (F) installed or programmed by anyone other than as detailed by the owner's manual for this
product.
STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at any time while this warranty is
in effect, warrantor will either, at its option, repair or replace the defective unit and return it to you without charge for parts,
service, or any other cost (except shipping and handling) incurred by warrantor or its representatives in connection with the
performance of this warranty. Warrantor, at its option, may replace the unit with a new or refurbished unit. THE LIMITED
WARRANTY SET FORTH ABOVE IS THE SOLE AND
ENTIRE WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE
WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR
PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow this
exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights, and you may also have other rights which vary from state to
state. This warranty is void outside the United States of America and Canada. PROCEDURE FOR OBTAINING PERFORMANCE
OF WARRANTY: If, after following the instructions in the owner's manual you are certain that the Product is defective, pack
the Product carefully (preferably in its original packaging). Disconnect the battery from the Product and separately secure
the battery in its own separate packaging within the shipping carton. The Product should include all parts and accessories
originally packaged with the Product. Include evidence of original purchase and a note describing the defect that has caused
you to return it. The Product should be shipped freight prepaid, by traceable means, to warrantor at:
Uniden America Service
4700 Amon Carter Blvd.
Fort Worth, TX 76155
May be covered under one or more of the following U.S. patents:
4,797,916 5,426,690 5,491,745 5,493,605 5,533,010 5,574,727 5,581,598 5,650,790 5,660,269 5,663,981 5,671,248
5,717,312 5,732,355 5,754,407 5,758,289 5,768,345 5,787,356 5,794,152 5,801,466 5,825,161 5,864,619 5,893,034
5,912,968 5,915,227 5,929,598 5,930,720 5,960,358 5,987,330 6,044,281 6,070,082 6,0760,52 6,125,277 6,253,088
6,314,278 6,321,068 6,418,209 6,618,015 6,671,315 6,714,630 6,782,098 6,788,920 6,788,953 6,839,550 6,889,184
6,901,271 6,907,094 6,914,940 6,940,867 6,953,118 7,023,176 7,030,819 7,146,160 7,203,307 7,206,403
Other patents pending.
Uniden® is a registered trademark of Uniden America Corporation.
As an Energy Star® Partner, Uniden has determined that this product or product models meets the Energy
Star® guidelines for energy efficiency. Energy Star® is a U.S. registered mark.
|