Uniden Conference Phone 1360 User Manual

telephone interface. The termination on an interface may consist of any combination  
of devices subject only to the requirement that the sum of the Ringer Equivalence  
telephone number shows in the display.  
2. Lift the handset or press the speaker button and the number automatically dials.  
NOTE: Use the delete button to delete an incorrectly entered number.  
Making a Phone Call  
Reviewing CID Records  
Interference Information  
Base Layout  
Memory  
Model 1360  
1. Lift the handset or press the speaker button. Wait for a dial tone.  
2. Dial the telephone number you want to call.  
Press the review or buttons to view the call records.  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two  
conditions: (1) This device may not cause harmful interference; and (2) This device must accept any  
interference received, including interference that may cause undesired operation.  
You may store information in any of the following memory locations: 0 to 9, A, B, and C .  
See “Storing a Pause in Memoryand “Temporary Tone Dialingfor more information.  
Numbers of all the devices does not exceed ꢃve  
.
review (/)  
memory store  
buttons  
Press the review button to scroll through the call records from the most recent to  
the oldest.  
display  
buttons  
Call Waiting / Caller ID  
Speakerphone with  
12 Number Memory  
User’s Guide  
One-year limited warranty  
3. Replace the handset in the cradle, or press the speaker button to hang up.  
Caller ID Display Messages  
Storing a Name and Number in Memory  
1. Press the store button. The screen displays LOCATION?.  
2. Press the desired memory location (0-9, A, B, C).  
NOTE: You may select memory locations by pressing review or   
buttons to scroll through the memory locations or press the 0 - 9, A, B, C.  
3. Press the store button again to conꢃrm the memory location.  
NOTE: If necessary, to erase existing memories, or if you make a mistake,  
use the delete button.  
4. Use the number keys to enter the telephone number (up to 32 digits) and press the  
store button to save. (The unit will not dial a phone number in this mode.) The cursor  
automatically moves to the text line for name entry.  
5. Use the number keys to enter the name of the person associated with the telephone  
number you just entered. More than one letter is stored in each of the number keys.  
For example, to enter the name BILL SMITH, press the 2 key twice for the letter B. Press  
the 4 key 3 times for the letter I. Press the 5 key 3 times for the letter L.  
NOTE: The ꢀashing cursor automatically moves to the next position or  
you may press the reviewor buttons to move the cursor to the next  
position.  
Press the 5 key 3 times for the second letter L. Press the arrow key (4) two times to  
insert a space, and press the 7 key 4 times for the letter S. Press the 6 key once for the  
letter M. Press the 4 key 3 times for the letter I. Press the 8 key for the letter T. Press the  
4 key twice for the letter H.  
6. Press the store button to save the name.  
7. To enter another name and number in a diꢁerent memory location, return to step 1  
and repeat the process.  
This equipment has been tested and found to comply with the limits for a Class B digital device,  
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection  
against harmful interference in a residential installation.  
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular installation.  
Press the review button to scroll through the call records from the oldest to the  
newest.  
mute  
IMPORTANT: Evidence of original purchase is required for warranty service.  
WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”) ELEMENTS OF WARRANTY:  
Uniden warrants, for one year, to the original retail owner, this Uniden Product to be free  
from defects in materials and craftsmanship with only the limitations or exclusions set  
out below.  
Volume  
The following special messages indicate the status of a message or the unit:  
button  
You may adjust the handset and speakerphone volume independently with the  
VOL ( - or + ) buttons. Both handset receiver volume level and speakerphone volume  
level are saved in memory.  
BLOCKED CALL  
The caller of the incoming call is registered as  
“Private Numberand their Caller ID information is withheld.  
When all of the records have been viewed, The screen displays START/END.  
speaker  
button  
Deleting CID Records  
Battery power level is low.  
To delete the record shown in the display, press the delete button once.  
To delete all records while reviewing, press and hold the delete button for about  
three seconds. The screen displays DELETE ALL?. Press delete again to complete.  
Adjusting the Handset Receiver Volume  
VOL (+/-)  
buttons  
Privacy of Communications may not be ensured when using this product.  
NO CALLS  
The caller memory is empty.  
WARRANTY DURATION: This warranty to the original user shall terminate and be of no  
further eꢁect 12 months after the date of original retail sale. The warranty is invalid if  
the Product is (A) damaged or not maintained as reasonable or necessary, (B) modiꢃed,  
altered, or used as part of any conversion kits, subassemblies, or any conꢃgurations  
not sold by Uniden, (C) improperly installed, (D) serviced or repaired by someone other  
than an authorized Uniden service center for a defect or malfunction covered by this  
warranty, (E) used in any conjunction with equipment or parts or as part of any system  
not manufactured by Uniden, or (F) installed or programmed by anyone other than as  
detailed by the owner’s manual for this product.  
While using the handset, you can adjust the speaker volume by pressing the  
VOL ( - or + ) buttons. The screen displays volume.  
If this equipment does cause harmful interference to radio or television reception, which can be  
determined by turning the equipment oꢁ and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
• Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is  
“receivingthe interference).  
• Reorient or relocate and increase the separation between the telecommunications equipment and  
receiving antenna.  
• Connect the telecommunications equipment into an outlet on a circuit different from that to which  
the receiving antenna is connected.  
If these measures do not eliminate the interference, please consult your dealer or an experienced  
radio/television technician for additional suggestions. Also, the Federal Communications Commission  
has prepared a helpful booklet, “How To Identify and Resolve Radio/TV Interference Problems.This  
booklet is available from the U.S. Government Printing Oꢂce, Washington, D.C. 20402. Please specify  
stock number 004-000-00345-4 when ordering copies.  
Notice: The changes or modiꢃcations not expressly approved by the party responsible for compliance  
could void the user's authority to operate the equipment.  
START/END  
You are at the beginning or the end of the Caller ID memory log.  
ringer  
volume  
switch  
Dialing Back  
Adjusting the Speakerphone Volume  
PRIVATE CALLER The incoming call does not have Caller ID service or their service  
area is not linked to yours. If the screen displays PRIVATE  
CALLER along with a calling number, the name information for  
that number was not available.  
While using the speakerphone, you can adjust the speaker volume by pressing the  
VOL ( - or + ) buttons. The screen displays volume level.  
When reviewing Caller ID records, you can dialback the numbers on the display by  
pressing the dial button.  
delete  
button  
menu  
button  
NOTE: Both handset receiver and speakerphone volume return to the  
default setting (low) if the unit's power is reset.  
NOTE: If the screen displays PICKUP PHONE, no other changes to  
the number can be made. The information sent from the telephone  
company is known to be a valid number for dialing back (used only  
in very limited areas). Once you pickup the phone, the number is  
automatically dialed.  
If You Programmed Your Local Area Code  
1. Use the review or buttons to display the number you want to dial.  
2. Press the dial button.  
Redial  
Troubleshooting Tips  
store  
button  
You may redial the last number you called by pressing the redial button after you hear a  
STATEMENT OF REMEDY: In the event that the product does not conform to this  
warranty at any time while this warranty is in eꢁect, warrantor will either, at its option,  
repair or replace the defective unit and return it to you without charge for parts,  
service, or any other cost (except shipping and handling) incurred by warrantor or  
its representatives in connection with the performance of this warranty. Warrantor,  
at its option, may replace the unit with a new or refurbished unit. THE LIMITED  
WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY PERTAINING TO  
THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES OF ANY  
NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW,  
INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR  
FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE  
FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES.  
Some states do not allow this exclusion or limitation of incidental or consequential  
damages so the above limitation or exclusion may not apply to you.  
No Dial Tone  
dial tone.  
Check all cabling to make sure that all connections are secure and not damaged.  
Check hook switch: Does it fully extend when handset is lifted from cradle?  
No Display  
Replace the batteries.  
Check for proper battery installation.  
No Information is Shown After the Phone Rings  
Are you subscribed to Caller ID service from your local telephone company?  
Be sure to wait until the second ring before answering.  
Phone Dials in Pulse with Tone Service  
Make sure TONE PULSE is set to TONE DIAL.  
Phone Won’t Dial Out with Pulse Service  
Make sure TONE PULSE is set to PULSE DIAL.  
Phone Does Not Ring  
Make sure ringer switch is set to 1 or 2.  
You may have too many extension phones on your line. Try unplugging some  
extension phones.  
Check for dial tone. See Troubleshooting Tips for No Dial Tone.  
Incoming Voice Volume Low  
Are other phones off hook at same time? If so, this is normal condition as volume  
drops when additional phones are used at once.  
NOTE: The redial feature holds the last number (up to 32 digits) that you  
dialed in memory. If you pressed any other numbers after dialing the  
phone number (for example, when accessing a voice-menu system) then  
those numbers are also dialed.  
dial  
button  
If you see a number with seven digits (i.e. 555-1234), then the call is from within your  
area code. However, this does not guarantee the call is a local call.  
ꢀash/exit  
button  
redial/pause  
button  
Mute  
# button  
If you see a number with 11 digits (i.e. 1-234-555-1234), then the call is not from  
within your area code.  
Hearing Aid Compatibility (HAC)  
*tone  
Use the mute button to interrupt a phone conversation to talk privately with someone  
else in the room. A conversation can be muted while using the speakerphone or  
handset.  
button  
This telephone system meets FCC standards for Hearing Aid Compatibility.  
NOTE: A timer (10 seconds on-hook and 3 seconds oꢁ-hook) located in  
the upper right side of the display will start, letting you know how much  
time is left until the unit returns to the Summary Screen.  
3. If you are at on-hook and the screen displays PICKUP OR ADJ, you can adjust the  
phone number format by pressing the dial button. If the phone is oꢁ-hook and the  
screen displays ADJUST, you can adjust the phone number format by pressing the  
dial button. For example, sometimes a 7-digit local number cannot be dialed because  
it requires a 10-digit or 11-digit format. Press the dial button repeatedly to scroll  
through the 7, 10, and 11-digit numbers.  
Licensing  
Installing and Replacing the Batteries  
1. Press the mute button. The mute indicator illuminates.  
2. Press mute again to turn it oꢁ.  
NOTE: Switching from speakerphone to handset cancels mute.  
Licensed under US Patent 6,427,009.  
Your Caller ID phone uses 4 AA-size alkaline batteries for receiving and storing Caller ID  
records and for storing the numbers you use for memory dialing, pulse dialing, and redial.  
Changing a Stored Number  
FCC RF Radiation Exposure Statement  
Repeat the storage sequence under “Storing A Name and Number in Memory, and use  
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled  
environment. This equipment should be installed and operated with a minimum distance of 20  
centimeters between the radiator and your body. This transmitter must not be co-located or  
operated in conjunction with any other antenna or transmitter.  
the delete button to delete the old number before entering the new number.  
IMPORTANT: You will have approximately 90 seconds to replace  
the batteries before the memories stored are lost. Please read the  
instructions before replacing the batteries and have the batteries ready  
to be inserted beforehand.  
Flash  
LEGAL REMEDIES: This warranty gives you speciꢃc legal rights, and you may also  
have other rights which vary from state to state. This warranty is void outside the  
United States of America and Canada. PROCEDURE FOR OBTAINING PERFORMANCE OF  
WARRANTY: If, after following the instructions in the owner’s manual you are certain that  
the Product is defective, pack the Product carefully (preferably in its original packaging).  
The Product should include all parts and accessories originally packaged with the  
Product. Include evidence of original purchase and a note describing the defect that  
has caused you to return it. The Product should be shipped freight prepaid, by traceable  
means, to warrantor at:  
Erasing a Stored Number  
1. Press the store button.  
2. Press the memory location (0-9, A, B, C) to be erased.  
3. Press the delete button.  
Press ꢀash/exit to activate special features of your telephone network, such as call  
transfer, or special services from your local telephone company, such as call waiting.  
CAUTION:  
IMPORTANT: If you are not going to use the telephone for more than 30  
days, remove the batteries because they may leak and damage the unit.  
Temporary Tone Dialing  
7-digits:  
7-digit telephone number (i.e. 555-5555)  
RISKOFELECTRICSHOCK  
DONOTOPEN  
If you have pulse (rotary) service and want to access customer calling services (such  
as telebanking and long distance services) that require tone dialing, you can use this  
feature to temporarily change from pulse to tone service.  
10-digits:  
11-digits:  
3-digit area code + 7-digit telephone number (i.e. 425-555-5555)  
long distance code 1 + 3-digit area code + 7-digit telephone  
number (i.e. 1-425-555-5555)  
Copying Caller ID Memories to User Memory  
THE EXCLAMATION  
POINT WITHIN THE  
TRIANGLE IS A  
THE LIGHTNING  
CAUTION: TO REDUCE THE  
1. Disconnect the telephone line cord and remove the desk  
stand from the back of the base.  
2. Release latch or the battery compartments and remove  
cover.  
3. Insert 4 AA-size alkaline batteries as shown on the  
diagram in the battery compartments.  
4. Snap the battery compartment door back into place and  
replace the desk stand.  
FLASH AND ARROW RISK OF ELECTRIC SHOCK, DO  
HEAD WITHIN THE  
1. Press the review or buttons to view the caller number and name you want to  
WARNING:TO  
NOT REMOVE COVER (OR  
copy.  
WARNING SIGN  
ALERTING YOU OF  
IMPORTANT  
TRIANGLE IS A  
BACK). NO USER  
PREVENT FIRE OR  
ELECTRICAL SHOCK  
HAZARD, DO NOT  
EXPOSETHIS  
After dialing the telephone number and connecting to the customer calling service,  
1. Press and release the *tone button.  
2. When you hang up, the telephone automatically returns to pulse dialing mode.  
WARNING SIGN  
SERVICEABLE PARTS INSIDE.  
2. Press the store button.  
3. Press the memory location (0-9, A, B, C). The number ꢀashes if there is a number  
already stored in the memory location.  
4. Press the store button to enter the edit mode, and then press the store button again  
to edit the name.  
NOTE: You may select a diꢁerent memory location by pressing review  
or buttons to scroll through the memories or press a number key  
(0-9, A, B, C).  
4. To dial the displayed number, and the phone is on-hook, pick up the handset or press  
the speaker button before the timer reaches 0. If the phone is oꢁ-hook, wait until the  
time reaches 0. The screen displays NOW DIALING and the number is dialed.  
If You Did Not Program Your Local Area Code  
1. Use the review or buttons to display the number you want to dial. You will only  
see 10-digit numbers (i.e. 234- 555-1234).  
ALERTING YOU OF REFER SERVICING TO  
“DANGEROUS  
INSTRUCTIONS  
ACCOMPANYING  
THE PRODUCT.  
QUALIFIED SERVICE  
PERSONNEL.  
Uniden America Service  
4700 Amon Carter Blvd.  
Fort Worth, TX 76155  
Uniden® is a registered trademark of Uniden America Corporation.  
VOLTAGE” INSIDE  
THE PRODUCT.  
Check the handset receiver or speaker volume.  
Memory Dialing  
PRODUCT TO RAIN  
OR MOISTURE.  
SEE MARKING ON BOTTOM / BACK OF PRODUCT  
Speakerphone Basics  
Location  
Make sure you entered the numbers correctly into memory.  
The pictures in this manual are used for examples only. Your actual phone may not look  
exactly like the pictures.  
Introduction  
General Product Care  
5. Connect the line cord and check your memory locations.  
Your phone features a speakerphone for ease of use and convenience during a phone  
conversation. At any time during a conversation, you can lift the handset to stop using  
the speakerphone. Likewise, when you are using the handset, press the speaker button  
and place the handset in the cradle to switch to the speakerphone.  
2. See steps 2 through 4 in the previous section to complete the dialback process.  
CAUTION: When using telephone equipment, there are basic  
safety instructions that should always be followed. Refer to the  
IMPORTANT SAFETY INSTRUCTIONS provided with this product  
and save them for future reference.  
To keep your phone working and looking good, follow these guidelines:  
NOTE: If the low battery icon appears in the display, you need to replace  
the batteries. It is important that you replace the batteries as soon as  
possible in order to maintain Caller ID operation.  
Setting Up the Caller ID Menu  
Avoid putting it near heating appliances and devices that generate electrical noise  
(for example, motors or ꢀuorescent lamps).  
DO NOT expose to direct sunlight or moisture.  
Avoid dropping and other rough treatment to the unit.  
Clean with a soft cloth.  
Never use a strong cleaning agent or abrasive powder because this will damage the  
ꢃnish.  
Retain the original packaging in case you need to ship it at a later date.  
5. Press the store button to conꢃrm and save, and wait for three seconds to exit.  
NOTE: If the name you want to enter is longer than 12 characters, only  
the ꢂrst 12 characters will be copied into memory.  
You should not plug the telephone into the modular jack while setting up the Caller ID  
menu.  
Equipment Approval Information  
For best speakerphone performance, avoid the following:  
Installing the Phone  
Your telephone equipment is approved for connection to the Public Switched Telephone  
Network and is in compliance with parts 15 and 68, FCC Rules and Regulations and the Technical  
Requirements for Telephone Terminal Equipment published by ACTA.  
Short Glossary of Terminology Used in this Manual  
Areas with high background noise. (The microphone might pick up these sounds and  
prevent the speakerphone from going into the receiving mode when you ꢃnish talking.)  
1. Press the menu button to enter the menu feature conꢃguration mode.  
# 1. >ENG FRA ESP (CID language default English)  
# 2. CONTRAST (default level is 3)  
# 3. LOCAL AREA CODE  
# 4. TONE PULSE (Default is tone dialing).  
2. Press the menu button to scroll through the 4 menu screens.  
3. Use the or buttons to select the desired setting.  
NOTE: You have 20 seconds following an entry before the phone returns  
to the Summary Screen.  
Your phone should be placed on a level surface, such as a desk or table top, or you can  
mount it on a wall.  
Storing a Redial Number to Memory  
Hook switch. The part of the phone that pops up to activate the phone line when the  
handset is lifted from the base.  
Surfaces affected by vibration.  
Recessed areas such as in a corner, under a cupboard, or next to a cabinet, which can  
generate an echo eꢁect.  
1. Press the store button.  
1
Notiꢂcation to the Local Telephone Company  
Connecting the Handset  
Oꢁ-hook. A term used to describe the phone in its active mode when the handset is oꢁ  
of the base cradle or when the speaker button is pressed.  
On-hook. A term used to describe the phone in an inactive mode.  
2. Press any key (0-9, or quick call buttons A, B, or C) for the memory location. If there is  
a number already stored in the memory location it will appear on the display. Use the  
review or button to select a diꢁerent location.  
3. Press the store button again to conꢃrm.  
4. Press the redial button, and then press the store button again.  
5. Enter name, if necessary, and then press the store button to conꢃrm.  
On the bottom of this equipment is a label indicating, among other information, the US number  
and Ringer Equivalence Number (REN) for the equipment. You must, upon request, provide this  
information to your telephone company.  
The REN is useful in determining the number of devices you may connect to your telephone line  
and still have all of these devices ring when your telephone number is called. In most (but not  
all) areas, the sum of the RENs of all devices connected to one line should not exceed 5. To be  
certain of the number of devices you may connect to your line as determined by the REN, you  
should contact your local telephone company.  
A plug and jack used to connect this equipment to the premises wiring and telephone network  
must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A  
compliant telephone cord and modular plug is provided with this product. It is designed to be  
connected to a compatible modular jack that is also compliant. See installation instructions for  
details.  
1. Connect one end of the coiled handset cord to the jack on the handset.  
2. Plug the other end of the coiled handset cord to the jack on the base.  
3. Place the handset in the cradle.  
Speakerphone Use  
Service  
Note the following guidelines when using the speakerphone:  
Before You Begin  
If trouble is experienced with this equipment, for repair or warranty information, please  
contact customer service at 1-800-297-1023. If the equipment is causing harm to the  
telephone network, the telephone company may request that you disconnect the  
equipment until the problem is resolved.  
Connecting the Telephone Line  
The speakerphone works similar to a two-way radio in that you can only listen or talk  
at one time.  
Parts Checklist  
1. Connect one end of the straight telephone line cord to the jack on the back of the base.  
2. Connect the other end to a wall phone jack.  
Make sure your package includes the following items:  
NOTE: If you want to edit the number, press the store button again  
within three seconds. When you are ꢂnished, wait three seconds to exit.  
Stay reasonably close to the phone so that you can be clearly heard by the person to  
whom you are talking.  
Display Language  
3. Set the ringer volume switch located at the back of the base to  
the desired loudness.  
- Telephone will not ring.  
1 - Sound will be lowest.  
2 - Sound will be loudest.  
NOTE: The unit is properly installed if you pick up the  
handset and hear the dial tone. Otherwise, recheck  
all installation steps.  
This adjustment allows you to display the Caller ID prompts in English, French, or Spanish.  
1. Press the menu button until the screen displays ENG FRA ESP.  
2. Use the review or buttons to select ENG, FRA or ESP.  
3. Press the menu button again to save.  
This product may be serviced only by the manufacturer or its authorized service agents.  
Changes or modiꢃcations not expressly approved by Uniden America Corporation could  
void the user’s authority to operate this product. For instructions on how to obtain  
service, refer to the warranty included in this guide or call customer service at 1-800-  
297-1023.  
You can adjust the speaker volume by pressing the VOL ( - or + ) buttons.  
The speakerphone indicator light comes on when the speakerphone is in use.  
NOTE: Batteries must be installed for the speakerphone to operate.  
Dialing a Number Stored in Memory While On-hook  
1. Press the dial button.  
2. To select a memory, press any number key (0-9, A, B, C). The number in that memory  
location displays.  
NOTE: You may select a diꢁerent memory location by pressing review  
or buttons to scroll through the memories or press a number key  
(0-9, A, B, C).  
Notes  
Caller ID (CID) Features  
• This equipment may not be used on coin service provided by the telephone company.  
• Party lines are subject to state tariffs, and therefore, you may not be able to use your own  
telephone equipment if you are on a party line. Check with your local telephone company.  
• Notice must be given to the telephone company upon permanent disconnection of your  
telephone from your line.  
• If your home has specially wired alarm equipment connected to the telephone line, ensure the  
installation of this product does not disable your alarm equipment. If you have questions about  
what will disable alarm equipment, consult your telephone company or a qualiꢃed installer.  
Contrast  
Or refer inquiries to:  
IMPORTANT: In order to use all of the features of this telephone, you  
must subscribe to two separate services available from your local  
telephone company: the standard Name/Number Caller ID Service  
to know who is calling when the phone rings and Caller ID with Call  
Waiting Service to know who is calling while you are on the phone.  
This adjustment allows you to adjust the contrast of the display.  
1. Press the menu button until the screen displays CONTRAST.  
2. Use the review or buttons to select level 1, 2, 3, 4, or 5.  
3. Press the menu button again to save.  
2-Wire  
Uniden America Service  
4700 Amon Carter Blvd.  
Forth Worth, TX 76155  
Attach your sales receipt to the booklet for future reference or jot down the date this  
product was purchased or received as a gift. This information will be valuable if service  
should be required during the warranty period  
Handset Cord  
Desk stand  
Telephone Line  
Base  
(might be  
attached to the  
base)  
Cord  
3. Press the speaker button, or pick up the handset to dial the displayed number.  
Wall Mounting  
Handset  
Your speakerphone can also be mounted on a wall plate (not included).  
Dialing a Number Stored in Memory  
1. Lift the handset, or press the speaker button.  
NOTE: To prevent the handset from falling out  
of the cradle while the phone is hanging on  
the wall, you must switch both the handset  
hook and the desk stand to their wall-mount  
positions.  
Local Area Code  
CID Summary Screen  
Telephone Jack Requirements  
.
2. Press the dial button then press a memory location button.  
The telephone uses the programmed area codes to determine the number format to  
display when a valid Caller ID signal is received. Numbers that match the local area code  
are displayed as seven digits and are used for dialing back previous numbers. Entering  
your local area code will also help you immediately know if the call is local or long  
distance when viewing the CID records in the display.  
Wall plate  
The Summary Screen shows the current time, date, and number of new calls to review. It  
is displayed until any button is pressed.  
To use this phone, you need an RJ11C type modular telephone jack,  
which might look like the one pictured here, installed in your home.  
If you don’t have a modular jack, call your local phone company to  
ꢃnd out how to get one installed.  
US Number is located on the cabinet bottom.  
REN Number is located on the cabinet bottom.  
Cascade Dialing  
Purchase Date  
Name of Store  
Modular  
telephone  
line jack  
This process allows you to dial a succession of stored numbers from separate memory  
locations. This is useful when you must dial several sequences of numbers, such as with  
frequent calls via a telephone company long distance provider.  
NOTE: The number of new calls is displayed until all new calls have been  
reviewed.  
2
Rights of the Telephone Company  
Should your equipment cause trouble on your line which may harm the telephone network,  
the telephone company shall, where practicable, notify you that temporary discontinuance of  
service may be required. Where prior notice is not practicable and the circumstances warrant  
such action, the telephone company may temporarily discontinue service immediately. In case  
of such temporary discontinuance, the telephone company must: (1) promptly notify you of  
such temporary discontinuance; (2) aꢁord you the opportunity to correct the situation; and (3)  
inform you of your right to bring a complaint to the Commission pursuant to procedures set  
forth in Subpart E of Part 68, FCC Rules and Regulations.  
The telephone company may make changes in its communications facilities, equipment,  
operations or procedures where such action is required in the operation of its business and not  
inconsistent with FCC Rules and Regulations. If these changes are expected to aꢁect the use or  
performance of your telephone equipment, the telephone company must give you adequate  
notice, in writing, to allow you to maintain uninterrupted service.  
On the front of the base, pull the handset hook out of  
the slot. Rotate hook 180 degrees and ꢀip it from front  
to back. Slide it back into the slot.  
Receiving and Storing CID Calls  
Important Installation Information  
NOTE: If you make a mistake and want to start over again, press the  
delete button to erase all of the digits.  
For example  
Local access number of long distance company  
Authorization code (ID)  
Long distance phone number  
1. Pick up the handset or press speaker.  
2. Press dial button, then press number “6for the memory location.  
3. Press dial button, then press number “7for the memory location.  
4. Press dial button, then press number “8for the memory location.  
5. The number dials automatically.  
Memory location  
Industry Canada (I.C.) Notice  
This units receives and displays information transmitted by your local company. This  
information can include the phone number,date, and time ;or the name , phone number,  
date, and time. The unit can store up to 75 calls for later review. When the memory is full,  
a new call automatically replaces the oldest call in memory. The screen displays NEW for  
calls received that have not been reviewed. The screen displays REPT for calls received  
more than once which have not been reviewed.  
CAUTION: Disconnect the phone cord from the wall outlet  
before installing or replacing the batteries.  
6
7
8
Turn the base over. Press in on the tabs and remove  
Terminal equipment  
1. Press the menu button until the screen displays LOCAL AREA CODE.  
2. Use the number keys to enter the Local Area Code you want.  
3. Press the menu button to save.  
the desk stand from the back of the base.  
Never install telephone wiring during a lightning storm.  
Never touch uninsulated telephone wires or terminals, unless the telephone line  
has been disconnected at the network interface.  
NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment  
Technical Speciꢃcations. This is conꢃrmed by the registration number. The abbreviation,  
IC, before the registration number signiꢃes that registration was performed based on a  
Declaration of Conformity indicating that Industry Canada technical speciꢃcations were  
met. It does not imply that Industry Canada approved the equipment.  
Rotate the stand 180 degrees, and insert the hooks  
marked WALL into the notches marked WALL. Press  
in on the tabs and snap the stand into place.  
Dialing Mode  
Use caution when installing or modifying telephone lines.  
Never install telephone jacks in wet locations unless the jack is specifically  
designed for wet locations.  
This adjustment allows you to select tone (touch-tone) or pulse (rotary) dialing.  
1. Press the menu button until the screen displays TONE PULSE.  
Connect the telephone line cord to the wall jack and  
the phone. If desired, wrap any excess cord around  
the cord hooks as shown.  
Place the mounting slots over the pins on the wall  
plate, and slide the base down to lock it into place.  
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is marked  
on the equipment itself. The REN assigned to each terminal equipment provides  
an indication of the maximum number of terminals allowed to be connected to a  
2. Press the review or buttons to show the current dialing mode. The default is  
TONE dialing.  
3. To change the dialing mode, press the review or buttons. The display alternates  
between the two modes.  
4. Press the menu button again to save.  
NOTE: The phone will exit Set Up after 20 seconds if no buttons are  
pressed.  
Temporarily disconnect any equipment connected to the phone, such as faxes,  
other phones, or modems.  
Visit our website at: www.uniden.com  
Storing a Pause in Memory  
The redial button has dual functionality and becomes a pause button when the store  
button is pressed ꢃrst. It is valid only when storing a number into memory locations.  
Use the redial/pause button to insert a pause when a delay is needed in an automatic  
dialing sequence. For example, when you must dial a 9 to get an outside line or when  
you enter codes to access your long distance company.  
Telephone Basics  
You can use the telephone by speaking into and listening through the handset, or by  
using the speakerphone.  
Receiving a Phone Call  
REMINDER: The time and date are programmed automatically when the  
ꢂrst Caller ID record is successfully received after set up.  
Pre-Dialing  
1. Lift the handset or press the speaker button to answer the call.  
2. Replace the handset in the cradle or press the speaker button to hang up.  
1. With the handset on the cradle, enter the telephone number you wish to call. The  
Uniden America Corporation  
Model 1360  
Printed in China  
Ft. Worth, TX  
 

Texas Instruments Projector ep780 User Manual
Thermador Cooktop P24WK User Manual
Toastmaster Cooktop AM24SS User Manual
TomTom GPS Receiver GO GPS User Manual
Trilogy Touch Technology Computer Monitor T3 HB17A1 User Manual
Uniden Cordless Telephone DCT 746M User Manual
Vantec Computer Drive UGT IS602R User Manual
Viking Ventilation Hood VCWH User Manual
Vita Mix Blender DM User Manual
Vivitek Projection Television du6871 User Manual